- 1 - 20 of 127 SEARCH RESULTS FOR
- products (127)
- video (172)
The cut 40 plasma consumable kit is a must have for any plasma owner or new buyer.* (1) External nozzle* (1) Air diffusor* (5) Electrodes* (5) Nozzles Contains the essential consumables required to keep your unit operating in peak performance and eliminate the issue of needing a replacement parts in…
Consumables Kit for your MIG Welder* 2 Gas Nozzles* 20 Contact Tips (ten 0.023"/0.6mm and ten 0.030"/0.8mm)* Plastic Storage Case Kit includes a complete set of consumables for your Eastwood MIG135 or MIG175 Welder or any other MIG welder with a Tweco-style torch.
Item #51551 HVLP Needle Kit
Cap, Needle and Nozzle Kit for the Eastwood HVLP Gun 51550.
The cut 60 plasma consumable kit is a must have for any plasma owner or new buyer. it contains the essential consumables required to keep your unit operating in peak performance and eliminate the issue of needing a replacement parts in the middle of a job. Includes 1 ext nozzle, 1 air diffusor, 5…
…60 This tip is perfect for sheet metal cutting where it is necessary to be precise and accurate. This tip enables the use of lower air pressure and results in very little slag or metal prep after the cut is made. Do not exceed 40amps when using 0.8mm tip. Optimal use for this tip is for precision…
This is a replacement Torch (Gun) for the Eastwood MIG175. It comes ready to install with a nozzle, contact tip, and liner.
Concours HVLP Spray Gun with 1.2mm tip sprays-on a "show-car" finish...yet it's powered by your home compressor with only 4 cfm @ 29 psi!* Compatible with most home-shop air compressors * Requires only 4 CFM @ 29 PSI * Solvent & Water-borne compatible * Lightweight aluminum body * Precision machined…
Contains all the consumables needed to service the Eastwood MIG 250 welder. 5 different tip sizes, 2 nozzles, 2 insulators and 2 tip holders.
Replacement drive roller for the Mig 250. This would be utilized if the original drive roller is damaged or lost. 0.035 and 0.045 wire
0.035 Inch Contact tips for use with MIG250 0.035 wire.
MIG Flux Core Contact Tip 0.035" for use with 0.035" MIG or Flux Core Wire. Compatible with Tweco and Clarke style guns. For Use With: * Eastwood MIG 135* Eastwood MIG 175* Eastwood 90 Flux Core
0.045 Inch Contact tips for use with MIG250 0.045 wire.
Designed to be used with Evercoat Maxim two-component cartridges. For use with 20536, 20537, 20538, 20539, 20540, 20451, 20452, 20543 and 20544. 1 mixing tip
Includes 10 replacement electrodes for the Eastwood Versa Cut 60 Plasma Cutter.
The Trim Tip for the Stud Welder allows you to quickly weld trim retaining clips to your vehicle. Easy to use, just slide in the Trim Tip, insert a Trim Rivet, gently push the Stud Welder against the surface until the outer ring makes contact, then trigger the gun for.5 to 1 second for a perfect…
Perfect Detailers. Stop using match sticks! Disposable micro-brushes with non-linting, non-absorbing tips are perfect touch-up tools. Reach into the tightest spots.
MIG 250 Flux Core Contact Tip 0.023 for use with 0.030 MIG or Flux Core Wire.
MIG Flux Core Contact Tip 0.030" for use with 0.030" MIG or Flux Core Wire. Compatible with Tweco and Clarke style guns. For Use With: * Eastwood MIG 135* Eastwood MIG 175* Eastwood 90 Flux Core
Top off your exhaust system with Pypes Stainless Steel Polished Tips and Splitters. These tips are model-correct, look great and are super-durable. Slip-fit construction makes installation a snap. Includes two tips. Pypes part number EVT80.
MIG Flux Core Contact Tip 0.023" - 0.025"(0.6mm) for use with 0.023" - 0.025"(0.6mm) MIG or Flux Core Wire.Compatible with Tweco and Clarke style guns. For Use With: * Eastwood MIG 135* Eastwood MIG 175* Eastwood 90 Flux Core