- 1 - 18 of 18 SEARCH RESULTS FOR
- products (18)
- video (20)
…to weld-shut a hole in the middle of a panel.* Weld material won't stick to copper head* For holes up to 1" in diameter* Perfect for use with your MIG, TIG or stick welder With this versatile tool, you'll leave your 2 hands free for welding while the copper head backs-up that hole. Strong magnetic…
Use for repairing small holes, rips or voids between panels. Copper "spoon" supports your welding from behind. Also acts as a heat sink to prevent warpage.
Plugweld Pliers makes it easier to use your MIG welder for plugging small holes in metalPlugweld Pliers clamps and supports the weld area, compressing the panels for tight plug welding.* Copper pad eliminates problem of burn-thru* Weld won't stick to copper pad* "U"-shaped jaw put pressure all…
Stud Welder Dent-Pulling System makes a hole-free dent repair, so it won’t weaken the panel, and needs less filler.* Stud welder spot-welds pins onto the dented metal surface* Pull the pins to pull-out the dent* Snip the pins, then grind the rest down 3-step repair works without drilling holes, so…
Copper "Welder's Helpers" plug holes as they support your welding in tight spotsUse these three 100%-copper "spoons" to back-up small holes, rips or voids between flat, round and angled panels while you weld.* 90-Degree Angle Plate* Curved Plate* Offset Flat Plate
…it's Eastwood priced for the DIYer!* Punches 3/16” holes* 7/8" Flange width* Air Consumption 4 CFM; Max Air Pressure 90 PSI* Works on up to 16 Gauge Mild Steel or 18 Gauge Stainless Steel This 2 in 1 pneumatic tool easily punches holes and flanges edges in sheet metal for creating and installing…
This pack includes 2 double-ended 3/16" high-speed steel drill bits with 135° cutting angle. 2.25" long. These are perfect for use when plug welding 20-ga. sheet metal.
…helps you weld without burning holes.* Prevents warping and weld burn-thru* Welding material won't stick to copper* 4" and 8" copper panels are magnetic; no hands or clamps needed Two magnetic copper backing panels provide hands-free support when doing butt-welding or welding holes in sheet metal.
Professor Hammer shows every detail of hammer dolly work . Also details on heat shrinking, hole filling, metal shaping, wired edge repair, rust repair and fitting patch panels
…18 gauge* Proper weld-prepped edges allow strong, flush, crack-free welds in sheet metal* The convenient hole punch feature provides clean, burr-free 0.19” holes A must for the beginning welder and professional alike. Minimizes blow through and warpage when joining panels. Great for patch panels or…
The Neatest Way to Fill Holes .....Is with this universal set of copper plates. Temporarily clamp over the hole or void, and weld. The weld-deposited metal will not stick to the copper, while the copper absorbs the heat. Soft annealed triangle can be bent to fit body contours. Use flat rectangles on…
…For 18-gauge steel, or if you're using a less-than-175-amp MIG welder, simply use the supplied double-ended HSS drill bit to drill a 0.187" pilot hole in the top panel only, and then complete the spot weld as usual. The pilot hole serves to assure complete and full penetration from the top to the…
…Backer helps you weld without burning holes.* Prevents warping and weld burn-thru * Welding material won't stick to copper * 2" x 8" copper panel is magnetic; no hands or clamps needed Magnetic copper backing panel provides hands-free support when doing butt-welding or welding holes in sheet metal.
Fill Holes in Sheet Metal Without Burn-Through - The rectangular copper paddle measures 1-5/16" wide by 6 1/8" long. This flat copper plate is clamped onto the metal and then welded from the other side. Weld deposited metal will not stick to the copper while the copper absorbs heat and prevents burn…
Fill Holes in Sheet Metal Without Burn-Through - The soft annealed copper paddle tapers down from 2-1/2" over its 7 1/4" length. Readily formed to match most contours this copper plate is clamped onto the metal and then welded from the other side. Weld deposited metal will not stick to the copper…
…Backer helps you weld without burning holes.* Prevents warping and weld burn-thru* Welding material won't stick to copper* 2" x 4" copper panel is magnetic; no hands or clamps needed Magnetic copper backing panel provides hands-free support when doing butt-welding or welding holes in sheet metal.
Fixturing, set-up table for precision fabrication and welding. 24-inch x 36-inch with 11-gauge steel top. Complete with leg kit; or use on tabletop. Holes are 16 mm with 2-inch spacing. Includes 4 clamps, 8 magnetic rests, 4 position stops, 4 inserts stops, 4 stop bars and 4 threaded adapters for…
…tool. Use to back up the weld area on thin gauge materials. The Mig or Tig fillers metals will not adhere to the copper plate and will eliminate holes. The tool has a magnetic base that can adjust the copper pad to fit securely at the weld area. Simply adhere to the back side and begin stitch…